Husky FLEX-NA-EKITBB Installationsanleitung PDF herunterladen (Seite 6)

6 | MIH-PIPING01-EN ORIGINAL INSTRUCTIONS

WARNING!

Extremely ﬂammable.

Keep away from open ﬂame and sparks. Use only in a well ventilated area.

KEEP OUT OF REACH OF CHILDREN.

FIRST AID!

» CONTAINS METHYLETHYLKETONE (MEK) AND

CYCLOHEXANONE.

» If swallowed, call a doctor or poison control center immediately.

AVOID!

These improper methods trap debris. This will slow down the airﬂow inside the

piping network and allow debris to accumulate in the lower level inlets.

INCORRECT

Rather try the following methods:

CORRECT

LOW VOLTAGE REMOTE CONTROL

Each vacuum inlet must be connected to low voltage remote control wiring to control the Power Unit remotely.

IMPORTANT!

The wiring network must be protected against moisture. Use the wiring provided

by Nuera Air.

NOTE

» For central vacuum systems equipped with basic wireless or two-

way wireless technology, low voltage wiring does not need to be

installed.

It is easy to have the wiring follow along with the piping and

make connections at each piping intersection. Connect wires

of the same colour together using 2 wire nuts. If all the wires

are the same colour, make sure that the wires going in 3

different directions are connected (from the 3 pipes)/ Do the

same with the 2nd set of wires.

Keep the wiring in place every 4 to 6 feet (1.2m) by using:

• wire ties (TUY-57)

• pipe supports (TUY-45)

• or electrician’s tape

• or 1/2in. (12mm) pipe split lengthwise

CAUTION!

Ensure that low voltage wires do not come into contact with another current

source, which could result in electrocution.

JackeTed low volTage wiring?

Jacketed wiring is recommended since it offers mechanical protection to the low voltage wiring. Wires may be pulled

in or ﬁshed afterwards, if necessary.

A Jacket is essential if:

• it is installed in concrete or buried in gravel.

It is not required if:

• the wiring is exposed along the piping.

COMMON COMPONENTS OF INSTALLATION KITS

TUY-61

Piping

Piping included in Nuera installation kits is specially designed to

be used with central vacuum system components. Only use piping

provided in the Nuera kits.

TUY-19

Long

Elbow

Within the piping system, use only long 90° elbows and avoid

short elbows!

TUY-21

Long 90°

Tee

The Long 90° Tee is the most commonly used for junctions.

TUY-24

45° Elbow

The 45° connector is very convenient. It allows for multiple

combinations to be made to bypass obstacles without excessively

reducing the vacuum efﬁciency.

TUY-99

Universal

Short 90°

Elbow

This connector must only be used to connect the vacuum inlet to

the piping circuit. It is versatile since it is compatible with partition

walls of different thicknesses.

TUY-35

Ring with

Stop

This ring is used to connect two aligned pipes.

TUY-45

Pipe

Support

Use a pipe support every 48 ins.(1.2m) to 60 ins. (1.5m). Low

voltage wiring can also be hung from them.

TUY-57

8ins (20 cm) wire ties

Attached low voltage wiring to the piping using these wire ties..

OTHER COMPONENTS AVAILABLE

TUY-37

Male-female Ring

This ring may be used if a pipe that is too short has been

cemented to connect it in a branch or to distance the elbow from

the mounting plate of a vacuum inlet.

TUY-27 &

TUY-26

38° or 30°

Elbow

These elbows are alternatives to other ﬁttings when the angle

between pipes is less than 45°.

TUY-29

45° Wye

This connection is multipurpose. When used with a 45° Elbow, two

parallel pipes can be connected together.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Husky FLEX-NA-EKITBB Installationsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Husky FLEX-NA-EKITBB